'Gesell's Automotive Service'

When winter approaches in Oconomowoc WI, we break out the sweaters, coats, boots and mittens. We want to be ready for winter conditions. Your vehicle needs to be ready for winter as well. The last thing you want is to get stranded out in the cold. You need your vehicle to be safe and reliable. It’s a good idea to get caught up on any neglected maintenance items anytime – but the stakes are higher in the winter.

There are some specific things that we need to do in Oconomowoc WI to have our vehicle ready for winter. The most obvious is having the antifreeze checked. If the antifreeze level is too low, it can’t properly protect your engine, radiator and hoses from freezing. If your car does not seem to be making enough heat to keep you warm, your antifreeze level may be low or you could have a thermostat problem. Get it checked out. If you are due for a cooling system service, now is a perfect time to have it done.

In the cold months around Oconomowoc we always worry about being able to stop in time when it’s slick out. The first thing to remember is to slow down and allow yourself plenty of room to stop. Of course, you want your brakes to be working properly. A thorough brake inspection will reveal if the pads or any other parts need replacing. Check with your service consultant to see if it is time to replace your brake fluid. It accumulates water over time which really messes with your stopping power.

It is a really good idea to have your battery tested. A battery’s cranking power really drops with the temperature. If your battery is weak in the fall, it may not be up to winter. There is nothing like a dead battery in a snow storm.

Which leads us to an emergency kit. You should always have a blanket or something to keep you and your passengers warm if you get stranded. If you will be venturing away from civilization, pack more items such as food and water to help you survive. Keeping at least half a tank of gas is a good precaution if you get stuck and need to run the car to keep warm and it will help keep your gas lines from freezing up.

Gesell’s Automotive Service
N6335 Hwy F
Oconomowoc, WI 53066
262-593-2715

Winter in Oconomowoc WI always makes us think of our windshield wiper blades – usually during that first storm when they aren’t working right. That’s why it’s a really good idea to replace your blades in the fall before the winter storms. If you live where there’s a lot of snow and ice, you might want a special winter blade that resists freezing up. And be sure to have enough windshield washer fluid.

The final thing to consider is your tires. Any tire can lose pressure over time – up to one pound every six or eight weeks. For every 10 degrees the temperature drops you lose another pound of pressure. So if it was 80 degrees outside when you checked your tire pressure two months ago and now it’s 40 degrees out, you could be down 5 pounds of pressure. That’s enough to be a real safety issue and it wastes gas too. You may need special winter tires as well. Your tire professional can help you find the right tire design for your expected road conditions.

If you’re getting winter tires, it is always best to put them on all four wheels. If you are only getting two, have them put on the rear – even if you have a front-wheel drive or four-wheel drive vehicle.

This is a very important safety measure recommended by tire manufacturers. Sliding or fish-tailing on ice and snow is a matter of not having enough traction at the rear end. That is why your newest tires should always be on the rear.

So, when are your tires actually worn out? This is a question a lot of us in Oconomowoc WI ask ourselves. For many, the answer is ‘when they no longer pass a safety inspection’. But waiting that long can have a serious impact on your safety.

The U.S. Federal government doesn’t have any laws for tread depth, but 42 of the states, and all of Canada, do have regulations. They consider two-thirty-seconds of an inch to be the minimum legal tread depth. Two other states, including California, consider one-thirty-second to be the minimum and six states have no standards at all. Call us at Gesell’s Automotive Service (just call 262-593-2715) to find out what your requirements are in the Oconomowoc WI area.

Since 1968, U.S. law has required that a raised bar be molded across all tires. When tires are worn enough that this bar becomes visible, there’s just 2/32” of tread left. But does that older standard give you enough safety?

Well, Consumer Reports issued a call to consider replacing tires when tread reaches 4/32”. And the recommendation is backed by some very compelling studies. Now before we go into the studies, you need to know that the big issue is braking on wet surfaces.

We tend to think of the brakes doing all the stopping, but you also need to have effective tires to actually stop the car. When it’s wet or snowy in Oconomowoc WI, the tread of the tire is critical to stopping power.

Picture this: you’re driving over a water-covered stretch of road. Your tires actually need to be in contact with the road in order to stop. That means the tire has to channel the water away so the tire is actually contacting the road and not floating on a thin film of water – a condition known as hydroplaning. When there’s not enough tread depth on a tire, it can’t move the water out of the way and you start to hydroplane.

This is where the studies come in. We think you’ll be surprised. A section of a test track was flooded with a thin layer of water. If you laid a dime flat on the track, the water would be deep enough to surround the coin, but not enough to cover it.

A car and a full-sized pick-up truck were brought up to 70 mph and then made a hard stop in the wet test area. Stopping distance and time were measured for three different tire depths. First, they tested new tires. Then tires worn to legal limits. And finally, tires with 4/32” of tread were tested – this is the depth suggested by Consumer Reports

When the car with the legally worn tires had braked for the distance required to stop the car with new tires, it was still going 55 mph. The stopping distance was nearly doubled. That means if you barely have room to stop with new tires, then you would hit the car in front of you at 55 mph with the worn tires.

Now with the partially worn tires – at the depth recommended by Consumer Reports – the car was still going at 45 mph at the point where new tires brought the car to a halt. That’s a big improvement – you can see why Consumer Reports and others are calling for a new standard.

Now without going into all the details, let us tell you that stopping the truck with worn tires needed almost 1/10 of a mile of clear road ahead to come to a safe stop. Obviously this is really a big safety issue.

The tests were conducted with the same vehicles, but with different sets of tires. The brakes were the same, so the only variable, was the tires.

So, how do you know when your tires are at 4/32”? Well, it’s pretty easy. Just insert a quarter into the tread. Put it in upside down. If the tread doesn’t cover George Washington’s hairline, it’s time to replace your tires. With a Canadian quarter, the tread should cover the numbers in the year stamp.

Now you may remember doing that with pennies. But a penny gives you 2/32” of an inch to Abraham Lincoln’s head. The quarter is the new standard – 4/32”.

Tires are a big ticket item and most people in Oconomowoc WI want to get the most wear out of them that they can. But do you want that much more risk just to run your tires until they are legally worn out? For us, and we would guess for many, the answer is “no”.

Well, Mr. Washington, let’s go out and look at my tires.

Gesell’s Automotive Service
N6335 Hwy F
Oconomowoc, WI 53066
262-593-2715

Most folks around Oconomowoc have had a flat tire. You know it’s inconvenient and a pain. Our tires are important. Keeping them in good working order isn’t just a big safety issue – it also has a financial impact. With high gas prices, we’ve all heard about the importance of keeping proper tire pressure to save on gas. In addition, proper inflation promotes even tread wear so your tires last longer.

There’s another danger to under-inflated tires. Low tire pressure puts added stress on the structure of the tire itself, causing it to break down prematurely. Also, under-inflated tires generate more heat which also reduces tire life. So get those slow leaks fixed quickly – don’t just keep airing them up every few days. You want to avoid serious tire damage.

Tires can also be damaged by road hazards in and around Oconomowoc. Punctures, cuts and impacts on curbs or potholes can also cause damage that could lead to tire failure. Sometimes, it’s something that a visual inspection would reveal. Take the opportunity to check your tires when you’re gassing up. Look for slashes, missing chunks, nails or screws in the tread or just uneven wear. Of course check the air pressure too.

Now tire damage can be on the inside where you can’t see it until it’s removed from the wheel. Such damage could come from a severe impact, driving on a flat or even just low pressure. Some punctures can cause internal damage that are too severe to be repaired. You may see our Gesell’s Automotive Service professionals take the time to remove your flat from the rim and inspect the inside before repairing it, which means we’re just following good procedure.

Now some tires just can’t be repaired. A puncture may be too large to plug. Also, the puncture could be in a location that’s not safe to repair like in the sidewall or outer portion of the tread. So called run-flat tires should not be repaired because their design is such that internal damage can’t be detected by a visual inspection.

It is also important that repairs should only be done by a qualified tire specialist like the ones we have at Gesell’s Automotive Service. You can buy self repair kits – save those for emergencies, like when you’re off-roading and need a quick fix so you can hobble back to civilization and get professional help. If you need to use a repair-in-a-can product, remember it’s a temporary measure only and your tire needs to be properly repaired as soon as possible.

Here are some other considerations: Repairing a flat may void your tire manufacturer’s warranty – just something to keep in mind. Also, if you repair a speed rated tire, you should not use it in any motorsports or operate it above legal speed limits. Your tire professional will repair your tire whenever it’s safe to do so and he’ll advise you when it’s better to replace it. So watch those curbs and keep the air – on the inside.

Gesell’s Automotive Service
N6335 Hwy F, Oconomowoc, WI 53066
262-593-2715

We all know that under inflated tires wear out more quickly. Under-inflation is also a major cause of tire failure. More flats, blow outs, skids and longer stopping distances are all results of under-inflated tires.

It’s hard to tell when a radial tire is under-inflated. If your manufacturer recommends 35 pounds of pressure, your tire is considered significantly under inflated at 26 pounds. The tire may not look low until it gets below 20 pounds.

Uncle Sam to the rescue! A new federal law requires manufacturers to include a Tire Pressure Monitoring System – or TPMS system – in all vehicles by the 2008 model year.

Some 2006 and 2007 models already have TPMS. The system is a dashboard mounted warning light that goes off if one or more of the tires falls 25 % below the manufacturer’s pressure recommendations.

The law covers all passenger cars, SUVs, mini vans and pick up trucks. The system must also indicate if it has a malfunction. This technology has been used by race cars for years. They are able to head off problems from under inflation by closely monitoring tire pressure on the track. It’s up to your car’s manufacturer to determine which of many TPMS systems available they’ll use to comply with the law.

Obviously, all of this doesn’t come free. Government studies have estimated the net costs. Of course, the TPMS system itself will cost something. Maintaining the system will have a cost, replacement of worn or broken parts and tire repair cost increases. The net cost is estimated to be between $27 and $100.

The costs are partially offset by savings in fuel and tread wear. There is also a saving in property damage and travel delay. Also, the government predicts fewer fatal accidents. They estimate there will be between $3,000,000 to $9,000,000 for every life saved.

Your safety has always been a concern of your service center. They want you on the road and accident free. They’ve traditionally provided things like tire rotations, snow tire mounting and flat fixes at a very low cost. They’ve been able to quickly and cheaply provide the service, and they pass the low cost on to you as an expression of their good will. That’s why they’re concerned about how you’ll perceive the changes that this new law will force.

Every time a tire is changed: taken off to fix a flat, a new tire installed, or a snow tire mounted, the service technician is now going to have to deal with the TPMS system. Sensors will need to be removed and reinstalled. The sensors will have to be re-activated after the change. And, unfortunately, the very act of changing the tire will damage some sensor parts from time to time – it’s inevitable and can’t be avoided.

Even a simple tire rotation will require that the monitor be reprogrammed to the new location of each tire. When a car battery is disconnected, the TPMS system will need to be reprogrammed. TPMS sensor batteries will need to be changed and failed parts replaced.

And the service centers themselves will need to purchase new scanning equipment to work with the TPMS sensors and to update expensive tire change equipment to better service wheels equipped with the new monitoring systems.

Service technicians will have to be trained on many systems and new tire-changing techniques. All of this adds up to significantly increased cost to the service center to perform what was once a very inexpensive service for you. So when you start so see the cost of tire changes, flat repairs and rotations going up, please keep in mind that it’s because of government mandated safety equipment. Your service center just wants to keep you safely on the road – and it’s committed to do so at a fair price. The effects of the new law will take some time to sort out, but it will help you avoid the most common vehicle failure, and possibly a catastrophic accident.

With the recent focus in Sullivan on improving fuel economy, we’ve been told how important it is to maintain our tire pressure.

Everyone in Sullivan knows that tires wear out, but we all want to make them last as long as possible because they’re fairly expensive to replace. In addition to saving gas, properly inflated tires last longer. Under-inflated tires will wear out more quickly.

Some people in Sullivan wonder if there is benefit to adding a few extra pounds of pressure when they fill up their tires. But actually, there isn’t. In fact, there are very good reasons not to over-inflate your tires. For one, the middle of the tread will wear unevenly because the full tread is not contacting the road properly. That also adversely affects your handling.

Come in and see us about tire maintenance for your Oconomowoc, WI vehicle.
Gesell’s Automotive Service
N6335 Hwy F
Oconomowoc, WI 53066
262-593-2715

Every vehicle in the Sullivan area has a sticker on the driver’s side door jamb that tells you the manufacturer’s recommended tire pressure. This recommendation is an integral part of the vehicle’s suspension tuning. A lot of engineering actually goes into the recommended tire pressure, so it’s important to follow it.

What else do we need to know about tire maintenance? Tire rotation and balancing are very important. Let’s start with rotation. Because the front tires handle the brunt of turning forces, the shoulders of the front tires wear more quickly than the rear tires. We rotate the tires so that they all get to do some duty on the front and they’ll all wear evenly over their life.

For most vehicles, front tires are rotated to the rear and vice versa. Others recommend a cross rotational pattern. Some vehicles use an asymmetrical tire so those tires need to stay on either the right or left side – it’ll say which on the tire. Some high performance cars have asymmetrical tires and different sizes on the front and rear. These can’t be rotated at all. Your owner’s manual will have details for your car.

How often should you rotate your tires? Your owner’s manual will have a recommendation. Your service advisor at Gesell’s Automotive Service can do a visual inspection to let you know if it looks like it should be done. The interval is typically around 5,000 miles.

You know, some people don’t think new tires need to be balanced. What they aren’t taking into account is the wheel. Between the wheel and the tire – even a new tire – there’s enough variation to require balancing.

When you add the valve stem and tire pressure monitoring sensors required on new cars, balancing is definitely in order. When a tire’s out of balance, it’s actually hopping down the road. You’ll feel the vibration through the steering wheel if a front tire’s out of balance and through your seat if it’s a rear tire.

Proper wheel balance promotes tire life and increases safety. Historically, lead weights have been attached to the wheel to bring it into balance. Lead gives some environmental concern, so steel weights are starting to be substituted.

Also, always use the same size tire on an axle. Different size tires on the front or on the back can lead to some real handling problems. And tire manufacturers recommend that when you get two new tires, they be installed on the rear because that’s where you need the most traction to avoid spinning-out.

Tires do a lot of work. They transfer engine power and braking forces to the road; they handle steering control; and they cushion all those bumps and jolts. They also support the entire weight of the vehicle, including you and your passengers. With such critical work to do, you want your tires to do their job well. And since replacing tires is fairly expensive, you want them to last as long as possible.

There are three keys to long, even tire wear:

• Proper tire inflation
• Proper wheel alignment
• Regular tire rotation and balancing

The front tires on a car take the brunt of the steering forces. As they push through turns, the shoulders of the front tires wear down more quickly than the rear tires. Rotating front and rear tires allows them to all wear at about the same rate. That’s especially true of front wheel drive vehicles whose front tires steer, and put the power to the road.

SUVs and pick-ups, especially four wheel drives, also tend to wear their tires more unevenly than cars because of their suspension and drive train set-up. Your owner’s manual will likely contain a schedule for tire rotation. It’s usually every 5,000 miles or so.

Also, there are different rotation patterns for different vehicles. Gesell’s Automotive Service will know which is right for your vehicle. That brings us to wheel balancing. When wheels are balanced, they spin on the axel evenly. When they are out of balance, they wobble a bit. That makes the tires wear unevenly and may transmit a vibration to the car. Your service technician at Gesell’s Automotive Service puts weights on your wheels to balance them out so that they turn true and smooth.

Tires are a big investment for any vehicle. They’re critical for keeping you safely on the road. The cost for regular rotation and balancing is more than made up in extended tire life. And, can you really put a price on your safety and that of your passengers?

Let me start by saying that your wheel bearings keep the wheels on your vehicle. Did that get your attention? In this article we’ll discuss more about wheel bearings and how you can keep them doing their very important job while you drive around Ixonia WI.

Come see us at: N6335 Hwy F Oconomowoc, WI 53066

Wheel bearings are pretty simple parts. They’re made of high quality steel and are engineered to last 100,000 miles or more if properly cared for. The bearings do two very important jobs: First they allow the wheel to freely rotate with as little friction as possible. Second, they support the weight of the vehicle. For example, if your car weighs 3,600 pounds, each wheel has to support approximately 900 pounds. That’s a lot of heavy lifting over many, many thousands of miles.

Even though wheel bearings are relatively simple, they need to be in near perfect condition to do their job. The bearings are packed with heavy grease to lubricate and protect them. A seal keeps the grease in and water and dirt out. It’s when the seal starts to leak that problems begin. The grease can become contaminated; causing the wheel bearings to overheat and ultimately fail.

The first sign that your wheel bearings are in trouble is an unusual noise coming from a wheel. It could be a chirping, growling, rumbling or a cyclic sound. The noise could get louder or even disappear at certain speeds. Your technician at Gesell’s Automotive Service can inspect for bearing wear by lifting the vehicle and checking for play in the wheel.

Now some wheel bearing assemblies are factory sealed. That means that they cannot be serviced – they can only be replaced. Those that aren’t sealed can be serviced on schedule. The bearings are removed, cleaned and inspected. If the bearings are still good, they’re re-installed – if not, they’re replaced. They are then packed in grease and a new seal is installed.

If your vehicle has a factory sealed wheel bearing assembly, the entire assembly needs to be replaced when trouble arises. Unfortunately, the parts are pretty pricy – but they usually last about 150,000 miles as long as the seals hold up.

Now, even a good seal cannot keep out water that’s exerting pressure on the seal. So if you’ve driven through hub deep water your bearings should be cleaned and repacked if they’re serviceable. If you have factory sealed bearings, you just need to watch for signs of premature failure.

If your wheel bearings can be serviced, your owner’s manual will recommend an interval, usually around 30,000 miles.

Now, if you have any sort of trailer, don’t forget its wheel bearings. They probably need to be serviced even more frequently. This is especially true for boat trailers that are used to launch the boat by backing it into the water. These should be serviced every year, usually at the end of the season so that the bearings don’t have the opportunity to sit and rust all winter.

So what happens if wheel bearings fail? Well, the wheel can literally fall off the vehicle. I don’t need to tell you how bad that could be. So check with your service advisor at Gesell’s Automotive Service and see if your vehicle’s wheel bearings can be serviced and when it’s recommended. Listen for warning signs. If you’ve been fording streams or puddle surfing after rainstorms, be especially vigilant.

Come by Gesell’s Automotive Service for a wheel bearing inspection, or for check engine light. Call for an appointment at 262-593-2715

Hey Oconomowoc, are your tires worn out? What is the standard for our WI streets? How can you tell on your minivan, suv?

While there may be legal requirements for the Oconomowoc area, there are safety concerns that go beyond meeting minimum replacement mandates.

2/32 is the depth of the tire tread wear indicator bars that US law has required to be molded across all tires since August 1, 1968. When tires are worn so that this bar is visible, there’s just 2/32 of an inch – 1.6 millimeters – of tread left. It’s that level of wear that’s been called into question recently.

We’re referring to the Consumer Reports call to consider replacing tires when tread reaches 4/32 of an inch, or 3.2 millimeters. And the recommendation is backed by some very compelling studies.

The issue is braking on wet surfaces in and around Oconomowoc. Most of us think of our brakes doing most of the work, but if you don’t have enough tread on your tires, the brakes can’t do their job. When it’s wet or snowy, the tread of the tire is even more critical to stopping power.

Picture this: you’re driving over a water covered stretch of road near Oconomowoc, WI. Your tires must be in contact with the road in order to stop. That means that the tire has to move the water away from the tire so that the tire is actually contacting the road and not floating on a thin film of water.

Floating on the surface of water is called hydroplaning. So if there’s not enough tread depth on a tire, it can’t move the water out of the way and you start to hydroplane.

In the study a section of a test track was flooded with a thin layer of water. If you laid a dime on the track, the water would be deep enough to surround the coin, but not enough to cover it.

A car and a full-sized pick-up were brought up to 70 miles per hour, or 112 kilometers an hour and then made a hard stop in the wet test area. Stopping distance and time were measured for three different tire depths:

• New tire tread depth
• 4/32 of an inch
• 2/32 of an inch

So what happened with the 2/32 tires on the car? Get this – when the car had traveled the distance required to stop with new tires, it was still going 55 miles an hour. Stopping distance was nearly doubled to 379 feet and it took 5.9 seconds.

Wow! That means if you barely have room to stop with new tires, you would hit the car in front of you at 55 miles an hour with the worn tires.

Now, with the partially worn tires – at 4/32 of an inch – the car was still going at 45 miles an hour at the point where new tires brought the car to a halt. It took nearly 100 feet more room to stop and 1.2 seconds longer. That’s a big improvement. We can see why Consumer Reports and others are calling for a new standard.

Of course, stopping distances were greater for the heavier pick-up truck.

How do you know when your tires are at 4/32 of an inch? Easy; just insert a quarter into the tread. Put it in upside down. If the tread doesn’t cover George Washington’s hairline, it’s time to replace your tires. With a Canadian quarter, the tread should cover the numbers in the year stamp.

You may remember doing that with pennies. A penny gives you 2/32 to Abraham Lincoln’s head. The quarter is the new recommendation – 4/32.

How do people feel about replacing their tires earlier? Well, tires are a big ticket item and most people want to get the most wear out of them that they can. But do you want that much more risk just to run your tires until they are legally worn out?

For us, and we would guess for many, the answer is “no”.

Gesell’s Automotive Service
N6335 Hwy F
Oconomowoc, WI 53066
262-593-2715

All new passenger vehicles on our Oconomowoc WI roads now have tire pressure monitoring systems – TPMS for short. They are designed to alert you if your tires are under inflated. Since they are fairly new, a lot of people have questions about TPMS.

First off, the most important thing is that you still need to check your tire pressure every week – or at least every time you gas up. The TPMS system alert comes in when your tire is twenty percent below the factory recommendation. So if the recommended pressure is thirty five pounds per square inch, the TPMS warning won’t come on until the pressure is at twenty eight pounds. That’s significantly under-inflated. Enough to raise safety concerns.

The worst is tire failure. A severely under inflated tire can overheat and fail. Also, handling degrades to the point that you may not be able to steer out of trouble. Also under-inflated tires wear out faster and they waste fuel. So it’s costly to not stay on top of proper inflation.

What’s the practical value of the TPMS system? Well, it’s twofold. First, it can alert you when your tire is losing pressure due to a puncture or a bent rim. That’s an important warning that you might not have gotten until next time you gassed up.

The second is that we all occasionally forget to check our tire pressure. So it’s a failsafe system to let you know there’s a problem brewing.

Other things can cause your TPMS system to go off. The system also monitors itself. The sensors that are mounted in the wheels have little batteries that send a signal to the monitor. The batteries go dead over time and the TPMS system will let you know. And the sensors could break. Also road salt from our Oconomowoc WI roads can ruin them.

There’s also a hassle factor that your Oconomowoc WI tire center has to contend with. For example, when you have your tires rotated in Oconomowoc, the TPMS system has to be re-calibrated so that it knows which tire is on which corner of the car. Same is true for when you have new tires or winter tires installed. Flat repairs, as well.

That takes extra time. And it requires the right equipment and training. Special – and expensive – tire change machines need to be used with some sensors. It’s all complicated by the fact that there are a number of different TPMS systems in use so the tire professionals at Gesell’s Automotive Service need equipment and training for each kind. Tire centers have had to raise the price of some of these basic services to offset their increased costs.

Also if you add custom wheels on your minivan, suv, you need to put in new TPMS sensors if your originals won’t work on the new rims. If you don’t your TPMS light will be on constantly and you won’t have the benefit of the warning system.

All in all, the mandated TPMS systems will save lives, so they’re worth the added hassle and expense.

It seems like everywhere you go around Oconomowoc you see custom wheels. Big trucks, little cars, mini-vans – it doesn’t matter, people are expressing themselves with custom wheels. Some people want smaller tires and wheels – some want larger – and some want them enormous. So where do you start if you want new wheels? We suggest you start with your budget. We know, that sounds so practical. But if the look you’re after goes beyond just new tires and wheels and enters into the world of suspension modifications, you need to be prepared for the additional cost.

Let’s start with something easy – you want to give your ride a unique look and the stock wheel size is just right for you. One of the concerns you will have is that the new wheels have the same offset as your factory wheels.

First, what is offset? The wheel bolts onto the hub on the car’s axel. The distance from the inside edge of the wheel to the point at which it bolts on, is the offset. If the new wheel has a different offset from the factory, the tires may rub on the inside or outside of the wheel well. That could lead to catastrophic tire failure.

Your Oconomowoc tire and wheel professional can help you find the right size wheel – or install adapters to make your new wheels fit. All you have to do is pick from the hundreds of styles available.

So, what if you want to upsize? Well, if it is just bigger wheels you want, but you want to keep the same overall tire diameter, that’s pretty easy. The same offset concerns apply. You need to know that the tires will likely be a little bit wider than the originals and could rub when you make sharp turns. A tire professional at Gesell’s Automotive Service can help you avoid this.

It is also important to keep the same overall tire diameter because changing the rolling diameter can mess with your anti-lock brakes and stability control systems. Are you starting to see why you want to consult with a tire and wheel expert? Is “super-size me” your motto? If it is, you are going to have to lift your vehicle to make room for those huge tires. A mild lift doesn’t require extensive modifications. An extreme lift means a lot of new hardware under the vehicle. It also means a lot of stock electronic systems need to be recalibrated to the new tire size. For example, your speedometer and odometer will give false readings if they aren’t recalibrated.

You should also be aware of possible performance issues. Bigger tires and wheels weigh more. Experts refer to this as unsprung weight because it isn’t held up by your suspension system. Increased unsprung weight affects performance in different ways than an equivalent amount of groceries or little soccer players in the passenger compartment. Acceleration is negatively affected. Stopping distances may also be increased – sometimes dramatically. If you want really big tires and wheels, you might need to upgrade your brakes to compensate.

Heading the other direction, some folks like to run smaller than standard wheels and lower the suspension. All of the same fitment issues still apply as well as calibration issues. Don’t think that suspension modifications are a bad thing. Many systems actually improve ride, function and performance over the stock set-up.

Regardless of your budget, you want your vehicle to continue to do all the things you need it to do. Some of those show cars and trucks you see on TV look fantastic, but have been modified in ways that may not suit your needs. For example, if you put large rims on your SUV with low profile tires, you may be in for busted rims if you go off-roading a lot. There just isn’t enough sidewall to absorb the impact of thumping over rocks.

Some people stuff the largest tires and wheels possible in their vehicles but have to severely restrict suspension travel so that the tires aren’t rubbing all day. That can lead to a very harsh ride. Again, talk with your Oconomowoc wheel professional about all of these things: how you drive, what look you are going for, your budget and what compromises you are willing to make.

At the end of the day, you’re going to be rollin’ out of there with one sweet ride.